- \n
- RTD Input<\/li>\n
- Temperature Output<\/li>\n
- Transmitter or Monitor<\/li>\n
- Voltage Detection<\/li>\n
- 100 Ohm Plat. Standard<\/li>\n
- 4-20 mA Output<\/li>\n
- 2 Buffered Outputs<\/li>\n
- 5 Selectable Ranges<\/li>\n
- Fault (OK) Detection<\/li>\n
- CSA & UL C1,D2<\/li>\n
- DIN Rail Mount.<\/li>\n<\/ul>\n
<\/div>\n
<\/p>\n
<\/p>\n
CMCP560 RTD Temperature Transmitter<\/strong> is compatible with 100 Ohm Platinum 3 wire RTD’s. Available in English scaling, the CMCP560 checks for faults, processes the temperature signal to determine overall amplitude, and outputs a 4-20 mA dc current that is proportional to a range of 0 to 250\u00b0 F (-17.7 to 121\u00b0 C). Combining transmitters with an existing PLC or DCS system results in a high density, low cost temperature monitoring system.<\/p>\n
<\/div>\n\nThe Optional Alarm Module provides ok, alert and danger relays, selectable time delay, trip multiply, bypass and 0 to 5 VDC outputs for displays. The relay outputs can be used to trigger machine shut-down or other alarms. Combining transmitters with an existing PLC or DCS system results in a high density, low cost vibration monitoring system.<\/p>\n
Alarms relays and trip multiply are available with the Monitor version.<\/strong><\/h3>\n
![\"CMCP500](\"data:image\/svg+xml;base64,PHN2ZyB3aWR0aD0iMSIgaGVpZ2h0PSIxIiB4bWxucz0iaHR0cDovL3d3dy53My5vcmcvMjAwMC9zdmciPjwvc3ZnPg==\")
<\/a>Alarms\u00a0– The CMCP500A Series Monitors have two independent set points, with LED alarm indicators and output relay contacts (Alert and Danger). Set points are adjustable via potentiometer, from 0 to 110% of full scale. Each has an adjustable delay of 1 to 10 seconds. SPST Relay contacts are rated 5 Amps @ 30 Vdc or 250 Vac for resistive loads.<\/p>\nRelay contacts can be independently configured by the user for either Normally Open (NO) (Standard) or Normally Closed (NC) operation. Relays are normally de-energized and can be configured for latching or non-latching (standard) operation. Latched alarms may be reset locally or by remote contact closure.<\/p>\n
Trip Multiply<\/strong>:<\/h3>\n
The monitors have set point multiplication of 3X via contact closure (2X available). To avoid tripping the alarms during machine start-up.<\/p>\n<\/div>\n
<\/div>\n<\/div>\nCustom Input and Output Configurations Available On Request<\/div>\n<\/div>\nFault Detection:<\/strong><\/h3>\n
On board fault detection circuitry continuously monitors the transducer for normal operation. If a fault occurs, the output current is reduced to <2 mA to indicate the fault to the readout system. A green LED on the front of the unit is turned off to provide a local indication of the fault.<\/div>\n<\/p>\n
<\/p>\n
<\/p>\n
Technical Specs:<\/span><\/h2>\n
\n<\/p>\n
\n\n
\n Electrical<\/th>\n<\/tr>\n \n Input:<\/strong> \u00a0100 Ohm Platinum RTD<\/td>\n<\/tr>\n \n Power:<\/strong> +24 Vdc @ 45 mA max. (30 mA typical)<\/td>\n<\/tr>\n \n Protection:<\/strong> Reverse polarity and transient protection<\/td>\n<\/tr>\n \n Frequency Response (wo\/filters):<\/strong> (-3 dB) 2 Hz to 20 kHz<\/td>\n<\/tr>\n \n Buffered Output:<\/strong> BNC Connector 0-20 kHz<\/td>\n<\/tr>\n \n Accuracy:<\/strong> 0.5 % of Full Scale Range<\/td>\n<\/tr>\n \n Output:<\/strong> 4-20 mA proportional to the full scale range<\/td>\n<\/tr>\n \n Maximum Load:<\/strong> 600 Ohms Resistive<\/td>\n<\/tr>\n \n Case:<\/strong> Isolated<\/td>\n<\/tr>\n \n Range:<\/strong> \u00a0English, 0 to 250\u00b0 F,
\nor Metric, -17.7 to 121\u00b0 C<\/td>\n<\/tr>\n\n Fault Indication:<\/strong> Green LED and 4-20 mA < 2mA<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n <\/p>\n<\/div>\n
<\/p>\n
\n\n
\n Optional Relay Module<\/th>\n<\/tr>\n \n Alarms:<\/strong> OK, Alert and Danger<\/td>\n<\/tr>\n \n Alarm Setpoints:<\/strong> Alert and Danger Adjustable 0 to 110% FS<\/td>\n<\/tr>\n \n Trip Multiply:<\/strong> 2X or 3X on Contact Closure<\/td>\n<\/tr>\n \n Alarm Relays:<\/strong> OK, Alert and Danger<\/td>\n<\/tr>\n \n Form C, SPDT, 5A @ 30 VDC or 250 VAC<\/td>\n<\/tr>\n \n Latching or Non-latching, Selectable<\/td>\n<\/tr>\n \n Time Delay:<\/strong> 0.1, 1, 3, 6 or 10 Seconds, Selectable<\/td>\n<\/tr>\n \n Alarm LED’s:<\/strong> Alert = Yellow, Danger = Red<\/td>\n<\/tr>\n \n Display Outputs:<\/strong> 0-5 VDC for Current Value, Alert Setpoint and Danger Setpoint<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n <\/p>\n
<\/p>\n
\n\n\n
\n Environmental<\/th>\n<\/tr>\n \n Operating Temp.:<\/strong> -20\u00b0C to +80\u00b0 C (-4\u00b0 F to +176\u00b0 F)<\/td>\n<\/tr>\n \n Storage Temp.:<\/strong> -55\u00b0C to +125\u00b0 C (-67\u00b0 F to +257\u00b0 F)<\/td>\n<\/tr>\n \n Relative Humidity:<\/strong> 0 – 95% Non-Condensing<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n <\/p>\n
<\/p>\n
\n\n\n
\n Physical<\/th>\n<\/tr>\n \n Mounting:<\/strong> 32 mm (G style) or 35 mm (T style) DIN Rail<\/td>\n<\/tr>\n \n Size:<\/strong> Transmitter 1.0″ Wide x 3.11″ High x 3.95″ Deep<\/td>\n<\/tr>\n \n w\/Relay Module 1.6″ Wide x 3.11″ High x 3.95″ Deep<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n <\/p>\n
<\/p>\n","protected":false},"excerpt":{"rendered":"
![\"CMCP500](\"http:\/\/www.stiweb.com\/v\/vspfiles\/assets\/images\/cmcp500-monitor-approval-label-v1.jpg\")
<\/a>Alarms\u00a0– The CMCP500A Series Monitors have two independent set points, with LED alarm indicators and output relay contacts (Alert and Danger). Set points are adjustable via potentiometer, from 0 to 110% of full scale. Each has an adjustable delay of 1 to 10 seconds. SPST Relay contacts are rated 5 Amps @ 30 Vdc or 250 Vac for resistive loads.<\/p>\n