<\/p>\n
Key features:<\/strong><\/p>\n <\/div>\n <\/p>\n <\/p>\n The CMCP545 Position (Thrust) Monitor<\/strong> is compatible with all manufactures Eddy Probe or Proximity Probe Systems with a voltage output of 100 or 200 mv\/mil and is available in English and Metric scaling. The CMCP545 checks for faults, processes the vibration signal to determine overall amplitude, and outputs a 4-20 mA dc current that is proportional to range of 0 to 80 mils (40-0-40) or the Metric equivalent of 0 to 2 mm (1.0-0-1.0 mm). Internal Jumpers select normal motion towards or away from sensor. Combining transmitters with an existing PLC or DCS system results in a high density, low cost vibration monitoring system.<\/p>\n The Optional Alarm Module provides ok, alert and danger relays, selectable time delay, trip multiply, bypass and 0 to 5 VDC outputs for displays. The relay outputs can be used to trigger machine shut-down or other alarms. Combining transmitters with an existing PLC or DCS system results in a high density, low cost vibration monitoring system.<\/p>\n Alarms relays and trip multiply are available with the Monitor version.<\/strong><\/p>\n Alarms\u00a0– The CMCP500A Series Monitors have two independent set points, with LED alarm indicators and output relay contacts (Alert and Danger). Set points are adjustable via potentiometer, from 0 to 110% of full scale. Each has an adjustable delay of 1 to 10 seconds. SPST Relay contacts are rated 5 Amps @ 30 Vdc or 250 Vac for resistive loads.<\/p>\n Relay contacts can be independently configured by the user for either Normally Open (NO) (Standard) or Normally Closed (NC) operation. Relays are normally de-energized and can be configured for latching or non-latching (standard) operation. Latched alarms may be reset locally or by remote contact closure.<\/p>\n Trip Multiply<\/strong>\u00a0– The monitors have set point multiplication of 3X via contact closure (2X available). To avoid tripping the alarms during machine start-up.<\/p>\n<\/div>\n Buffered Output:<\/strong><\/p>\n A BNC connector mounted on the front of the unit provides access to the buffered transducer output signal. This includes both the unfiltered vibration signal, and the DC bias voltage. Portable test equipment or analyzers can be connected to this output without disturbing other system outputs.<\/p>\n Fault Detection:<\/strong><\/p>\n On board fault detection circuitry continuously monitors the transducer for normal operation. If a fault occurs, the output current is reduced to <2 mA to indicate the fault to the readout system. A green LED on the front of the unit is turned off to provide a local indication of the fault.<\/p>\n Filters:<\/strong><\/p>\n <\/p>\n <\/p>\n <\/p>\n Technical Specs:<\/span><\/p>\n <\/p>\n <\/p>\n<\/div>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n","protected":false},"excerpt":{"rendered":" DATASHEET<\/a><\/p>\n\n
\n\n
\n Electrical<\/th>\n<\/tr>\n \n Input:<\/strong> Eddy Probe or Proximity Probe Systems (200 mv\/mil)<\/td>\n<\/tr>\n \n Power:<\/strong> +24 Vdc @ 45 mA max. (30 mA typical)<\/td>\n<\/tr>\n \n Protection:<\/strong> Reverse polarity and transient protection<\/td>\n<\/tr>\n \n Frequency Response (wo\/filters):<\/strong> (-3 dB) 2 Hz to 20 kHz<\/td>\n<\/tr>\n \n Buffered Output:<\/strong> BNC Connector 0-20 kHz<\/td>\n<\/tr>\n \n Accuracy:<\/strong> 0.5 % of Full Scale Range<\/td>\n<\/tr>\n \n Output:<\/strong> 4-20 mA proportional to the full scale range<\/td>\n<\/tr>\n \n Maximum Load:<\/strong> 600 Ohms Resistive<\/td>\n<\/tr>\n \n Case:<\/strong> Isolated<\/td>\n<\/tr>\n \n Range:<\/strong> English, 0-80 mils (40-0-40) or
\nMetric, 0-2 mm (1.0-0-1.0)<\/td>\n<\/tr>\n\n Fault Indication:<\/strong> Green LED and 4-20 mA < 2mA<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n \n\n
\n Optional Relay Module<\/th>\n<\/tr>\n \n Alarms:<\/strong> OK, Alert and Danger<\/td>\n<\/tr>\n \n Alarm Setpoints:<\/strong> Alert and Danger Adjustable 0 to 110% FS<\/td>\n<\/tr>\n \n Trip Multiply:<\/strong> 2X or 3X on Contact Closure<\/td>\n<\/tr>\n \n Alarm Relays:<\/strong> OK, Alert and Danger<\/td>\n<\/tr>\n \n Form C, SPDT, 5A @ 30 VDC or 250 VAC<\/td>\n<\/tr>\n \n Latching or Non-latching, Selectable<\/td>\n<\/tr>\n \n Time Delay:<\/strong> 0.1, 1, 3, 6 or 10 Seconds, Selectable<\/td>\n<\/tr>\n \n Alarm LED’s:<\/strong> Alert = Yellow, Danger = Red<\/td>\n<\/tr>\n \n Display Outputs:<\/strong> 0-5 VDC for Current Value, Alert Setpoint and Danger Setpoint<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n \n\n
\n Environmental<\/th>\n<\/tr>\n \n Operating Temp.:<\/strong> -20\u00b0C to +80\u00b0 C (-4\u00b0 F to +176\u00b0 F)<\/td>\n<\/tr>\n \n Storage Temp.:<\/strong> -55\u00b0C to +125\u00b0 C (-67\u00b0 F to +257\u00b0 F)<\/td>\n<\/tr>\n \n Relative Humidity:<\/strong> 0 – 95% Non-Condensing<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n \n\n
\n Physical<\/th>\n<\/tr>\n \n Mounting:<\/strong> 32 mm (G style) or 35 mm (T style) DIN Rail<\/td>\n<\/tr>\n \n Size:<\/strong> Transmitter 1.0″ Wide x 3.11″ High x 3.95″ Deep<\/td>\n<\/tr>\n \n w\/Relay Module 1.6″ Wide x 3.11″ High x 3.95″ Deep<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n